DBA 201 FSubwoofer Box | 440 W Peak Power | 200 mm super flat design | Plug & Play connection
High performance in a super flat design

 

The DBA 201 F flat active subwoofer enclosure optimized with FEM
simulation ensures superior performance, maximizing the subwoofer output
with ultra-compact size. The massive magnet of the 8 in. driver
provides optimal control during the highest cone excursion.

 

Internal 440-watt peak Class D amplifier
 

The Class D amplifier provides an unmatched
performance/size ratio, drawing less current from the vehicle's
electrical system. He-Li technology (high efficiency/low impedance) is
optimized for the 0.4 Ω load of the DBA 201 F subwoofer driver, and the
sealed enclosure.

Compatible with every car audio system

DBA
201 F can handle speaker-level signals up to 30 volts (1.2V – 30 V rms)
and includes USS for OEM systems and handles RCA line-level signals as
well (0.2mV – 5 V rms) from aftermarket systems. Thanks to the low
idling current and wide operating supply voltage (6.5V - 18V) DBA 201 F
is fully EV (Electrical Vehicle) friendly.

Plug & Play connection

The
DBA 201 F is designed to easily release via a Plug & Play Molex®
and harness, which includes the power connection. When you need extra
cargo room, you can quickly unplug and remove the box.

Extra full set of controls to fine-tune the in-car performance

The
built-in 24 dB/Oct. low-pass crossover filter with a variable cutting
corner frequency (50÷150 Hz) allows you to perfectly match the DBA 201 F
to your speaker system. Adjustable bass boost (0÷6 dB @ 45Hz) can add
bass output as you prefer, allowing correction for OEM sound
equalization. With the phase inverter (0-180°), you can optimize phase
alignment between the DBA 201 F and your speaker system, regardless of
the subwoofer’s position in the car. The subsonic filter (15 Hz @ 24
dB/Oct) protects the cone from over-excursion and amplifiers from
overheating. The input sensitivity control is the perfect tool to
maximize the overall system output level while preventing clipping.

Auto turn-on and standby mode

The
built-in audio sense circuit allows the DBA 201 F to turn on and
timeout to standby mode automatically. You can switch off the audio
sense function when a remote turn-on wire is available.

Provided remote-level control

DBA
201 F level can be adjusted (-15 dB ÷ 0 dB) using the new stylish HRC
01 remote control. HRC 01 AS control is ready for tape surface mounting,
screw surface mounting, and recessed mounting, thanks to the provided
accessories.

Watch the product video

The DBA 201 F flat active subwoofer enclosure optimized with FEM simulation ensures superior performance, maximizing the subwoofer output with a super flat size. The massive magnet of the 8 in. driver provides optimal control during the highest cone excursion.

Extra full set of controls to fine-tune the in-car performance

The built-in 24 dB/Oct. low-pass crossover filter with a variable cutting corner frequency (50÷150 Hz) allows you to perfectly match the DBA 201 F to your speaker system. Adjustable bass boost (0÷6 dB @ 45Hz) can add bass output as you prefer, allowing correction for OEM sound equalization. With the phase inverter (0-180°), you can optimize phase alignment between the DBA 201 F and your speaker system, regardless of the subwoofer’s position in the car. The subsonic filter (15 Hz @ 24 dB/Oct) protects the cone from over-excursion and amplifiers from overheating. The input sensitivity control is the perfect tool to maximize the overall system output level while preventing clipping.

Auto turn-on and standby mode

The built-in audio sense circuit allows the DBA 201 F to turn on and timeout to standby mode automatically. You can switch off the audio sense function when a remote turn-on wire is available.