Octave HP 700 SE pradinis stiprintuvas dažnių juosta: 10 Hz – 200 kHz  -0,7 dB, 0,7 Mhz -6 dB, subsoninis filtras: 15 Hz / - 3 dB, XLR | Nemokamas Pristatymas

"Octave HP 700" pradinio stiprintuvo istorija yra ilga ir sėkminga, o jo pagrindinės schemos ištakos siekia klasikinį HP 500 modelį, pirmą kartą pristatytą 1986 m. Ši koncepcija buvo nuosekliai plėtojama 30 metų ir sulaukė pasaulinio dėmesio.

HP700 SE - sophisticated valve technology combined with intelligent modularity make this pre-amp future-proof. A valve pre-amp boasting innovative precision technology and a modular concept that allows the listener the freedom to build a system to cater for individual music tastes. Instead of being bound by the fixed audio and technical parameters of the equipment, listeners can adapt the technology of the HP700 SE to their own requirements and preferences. The result is THE sound - the optimal sound experience for the individual high-end audio system and the individual listener. THE NEXT STEP - A major step toward the ideal of all music lovers.

PRECISION TECHNOLOGY IN THE LINE STAGE

Three amplification settings, combined with selectable output impedance, enable perfect fine-tuning of the HP 700 to the characteristics of the sound reproduction chain. The three-stage amplification settings allow optimal matching of the volume control to the efficiency of the speaker. The ability to select the output impedance – and therefore the output current – facilitates optimal set-up of the unit for the cable properties, cable length and cable capacity as well as for the input sensitivity of the output stage.

PSU TECHNOLOGY

In combination with the newly developed high-precision, low-noise supply-voltage stabilizing circuitry, the separate power supply unit for the HP 700 ensures constancy of the audio output even when the mains voltage is subject to wide fluctuations and high interference levels. Added to this, the integrated control logic system guarantees maximum operational reliability and, backed by our exclusive soft-start technologies, ensures the valves and the unit have a life of up to twenty years.

BYPASS

The multi-channel bypass function allows the HP700 to be integrated into an existing home-theater combination. The logic-controlled input selector circuitry allows selection of the bypass function for an XLR or phono input on the rear panel. The HT signal is present at all three outputs.

EXTERNAL POWER SUPPLY UNIT

The sophisticated design of the HP 700 makes extremely high demands on the power supply unit. The external power supply unit is magnetically screened and supplies a clean voltage to the HP 700 SE. The screening is also essential to ensure low- noise, low-hum operation of the phono MC input.

ADDITIONAL INDIVIDUALIZATION OPTIONS:

MODULAR INPUTS

The connection possibilities of the generously configured standard model are rounded off by two user-selectable optional input modules. An optimized input module can be used for unusual applications, for anything from an MC step-up transformer to a transformer-based XLR input module. The plug and play modules can be readily installed or upgraded at any time.

PHONO

Next-step technology has also been applied in the redesign of the Phono RIAA amplifier. The further development of the RIAA stage has improved the signal/noise ratio, while simultaneously reducing system-related distortion. The widening of the bandwidth enables accurate RIAA equalization and exploits the full potential of analog reproduction. The wide variety of optional input modules ensures that the optimal input can be installed for every pickup.

TONE CONTROL PRECISON TONE CONTROL

The innovative optional tone control rounds off the HP 700 SE equipment. The precision valve-based tone control unit guarantees consistency of the sound, even at low volume. Precision adjustment of bass and treble, with a 0.3dB channel separation, allows the tone to be adjusted without impairing the spatial reproduction.

BALANCE CONTROL

The frequency-compensated balance control allows channel-separated volume adjustment in 1 dB steps. This technology eliminates any controller-related sound shifts. Using 12-position stepped switches, the setting is longtime stable, with 100% repeatability.

OUTPUT SELECTOR SWITCH

The unit output can be switched to several zones by manual activation of the outputs. Whether the output is through XLR, phono or all three outputs simultaneously, a total of three output stages can be utilized for separate rooms, different speakers or bi and tri-amping.

STEPPED VOLUME CONTROL

The optional, frequency-compensated 47-position stepped switch ends the debate about the influence of the controller on the quality of the music signal. At 0.1dB, the channel deviation is supreme. Our own in-house development, the volume control design maintains the frequency bandwidth constant throughout the entire control range, reducing controller-related distortion to a scarcely measurable level.
However, as a result of the mechanical design of the stepped attenuator, the switch positions cannot be controlled using the remote control.

TECHNINIAI DUOMENYS

	Specifications
	In- and outputs
	Inputs		3 x RCA, 2 x XLR, 2 x arbitrary 1 x Bypass RCA (can be switched to IN4 -XLR)
	Outputs		2 x RCA, 2 x XLR, 1 x Monitor / Tape Record (RCA)
	XLR transmission ratio		0 dB
	XLR pin assignment		1 = ground, 2 = positive, 3 = negative
	Line stage
	Output resistance		100 / 300 ohms RCA; 150 ohm XLR
	Monitor Out output resistance		240 ohms
	Maximum output voltage		12V
	Gain factor Gain High		25 dB = 18,5
	Gain factor Gain Med		18 dB = 7,8
	Gain factor Gain Low		12 dB = 4
	Signal-to-noise ratio Gain High		- 98 dB / 38 µV at 3 V output voltage
	Signal-to-noise ratio Gain Med		- 104 dB / 18µV at 3 V output voltage
	Signal-to-noise ratio Gain Low		- 110 dB / 8 µV at 3 V output voltage
	Equivalent noise-level		14 nV √Hz
	Frequency response Gain High-RCA		10 Hz – 200 kHz  -0,7 dB, 0,7 Mhz -6 dB
	Frequency response Gain Med-RCA		10 Hz – 200 kHz  -0,3 dB, 1.3 MHz -6 dB
	Frequency response Gain Low-RCA		10 Hz – 200 kHz  -0,2 dB, 2,1 MHz -6 dB
	Frequency response XLR		10 Hz – 200 kHz  -1,5 dB
	Ramp-up time Gain Low		250 ns
	Ramp-up time Gain Low		60 V/µs
	Total harmonic distortion, Gain Low, Med, High		0.01% at 3V on 10 kOhm
	Channel separation		-90 dB / 1 kHz, Input short-circuited
	Crosstalk between inputs		- 80 dB / RCA, -95 dB XLR / 1kHz
	Input resistance		50 kOhm
	Channel matching via volume control		0,5 dB - 70 dB
	Phono
	RIAA equalization tolerance		0,3 dB / 15 Hz - 20 kHz
	Corner frequency - subsonic filter		15 Hz / - 3 dB
	Signal-to-noise ratio		- 75 / - 84 dB / with IN 2 MC Input
	Input sensitivity		250 µV / 600 µV / with IN 2 MC Input
			Input sensitivity, gain and input resistance depend on input module
	Gain MC Gain Low - Pre Out		Gain Low: 70 dB, Med: 77 dB, High: 83 dB
	Gain MC Gain High- Pre Out		Gain Low: 79 dB, Med: 86 dB, High: 92 dB
Download: Owner's Manual

	General Facts
	Power consumption		35 - 60 W
	Weight preamplifier		10 kg
	Weight power supply		3,8 kg
	Supplied accessories		Power calbe, remote control
	Dimensions of preamplifier (over-all)		462 x 130 x 480 mm (W x H x D)
	Dimensions of power supply (over-all)		110 x 90 x 277 mm (W x H x D)

Dimensions (in mm)     » The HP 700 SE is equipped with two RCA and XLR outputs. » The XLR output is transformer balanced and galvanically isolated. » Soft start for heating, power supply and signal output; providing maximum tube life and trouble-free switching on and off. » The gain of the Line-stage can be switched in three levels. » External power supply with multiple shielded power transformer and integrated mains filter.     Frequency response:       Frequency response and gain of line stages in Gain Low (12 dB), Med (18 dB), and High (25.5 dB) settings.     Line stage hum and noise level:       No mains interference can be detected during noise level measurement either; the noise level decreases linearly by 6 dB for each gain setting.     FFT interference spectrum:       Comparison of the RCA and XLR interference spectrum. No mains interference on either of the inputs; the spectrum of the harmonics K2, K3, K4, K5, K6 decreases consistently linearly for both outputs.     Phono frequency response with and without subsonic filter:       The frequency range without subsonic filter is very linear and extremely low (red graph). With the subsonic filter (cyan graph), bass reproduction is not limited by the low corner frequency (-3 dB at 15 Hz).     Control characteristics of the tone control:       The control range encompasses the area between the red and blue graphs. The precisely adjustable controls allow for settings in the 1 dB range based on the scale. One scale mark corresponds to +/- 4 dB.     Control range and balance control frequency response: