Turite klausimų? +370 698 34349 

JBL SDA-2200 2-jų Kanalų Garso Stiprintuvas 2 x 4Ω / 8Ω, 20Hz – 20kHz: 380W / 225W dažnių juosta 20 - 20kHz +/-0.05dB | Nemokamas Pristatymas

Būsena: Prekyboje

4 760,00 €

Nemokamas pristatymas per 0-3 darbo dienas.

Klauskite apie prekę / Siūlykite savo kainą / Derėkites

ŽEMIAUSIOS KAINOS GARANTIJA!

Mes pasiūlysim geresnę kainą ir duosime Jums papildomą nuolaidą iki 100 Eur! Tiesiog palikite užklausą arba paskambinkite mums.

JBL

Produkto aprašymas

JBL SDA-2200 2-jų Kanalų Garso Stiprintuvas 2 x 4Ω / 8Ω, 20Hz – 20kHz: 380W / 225W dažnių juosta 20 - 20kHz +/-0.05dB | Nemokamas Pristatymas

SDA-2200 Galingas ir dinamiškas garso stiprintuvas

Class G amplification offers the best characteristics Class A and Class A/B designs. Conventional Class A designs do not suffer from crossover distortion and is exceptionally transparent offering a high level of realism. However, a solely Class A design is extremely inefficient as it will always be drawing full power even with no signal to amplify, for this reason Class A amplifiers usually offer lower power output. Class AB design is a much more common and far more efficient than pure Class A, but it suffers from crossover distortion at low levels which clouds spatial details and transparency.

Class G offers greater efficiency and transparency, with less wasted heat energy than class A. Like a hybrid car engine, Class G implements multiple power supplies rather than just a single supply. The first power supply is of lower power and within this region the SDA-2200 runs in pure Class A, which has no crossover distortion. If a dynamic signal is received that goes beyond the capability of this first power supply, the secondary supply is gradually brought in up to full rated power output as required. This gives a very efficient design as additional power is only used when required. Modern high speed silicon allows us the make this switch at speeds well beyond the audio bandwidth.

Flexible

The SDA-2200 features Dante™ audio networking so you can connect with the JBL Synthesis SDR-35 AVR and SDP-55 immersive surround sound processor as well as other Dante-enabled products over Ethernet-based networks via an Cat5e or Cat 6 cable. Dante audio networking uses standard IP networks to transmit high-quality, uncompressed multi-channel audio with near-zero latency. It's the most flexible, reliable, and easy-to-manage audio networking solution available, and provides the lowest cost of ownership by dramatically reducing cabling and labor costs as well as eliminating issues with interference, crosstalk and signal degradation associated with analog cable. The SDA-2200 is capable of receiving hi resolution audio (up to 24 bit /192k ). Signal routing and system configuration with Dante is fast, simple, and incredibly flexible. Once the network is configured, signal routing and other system settings are stored safely in the Dante devices themselves, so they are automatically restored if a device is power-cycled.


SDA-2200 Savybės

  • Dynamic Class G amplification
  • Dante™ audio networking
  • 200 watts @8 Ohms 1100 watts bridged @ 4 Ohms
  • Balanced and single ended inputs
  • Trigger in and out
  • Ethernet, RS232 control

Specifikacijos

Two channels driven, 4Ω / 8Ω, 20Hz – 20kHz: 380W / 225W
One channel driven, 8Ω bridged mode, 20-20kHz: 790W
Harmonic distortion, 80% power, 8Ω at 1kHz: 0.001%
Input sensitivity 200W / 8Ω: 1.15V RMS (RCA Type), 2.3V RMS (XLR Type)
Signal/Noise ratio (A-wtd) 50W / 8Ω: 110dB
Input impedance: 10kΩ
Frequency response: 20 - 20kHz +/-0.05dB
Mains voltage: 110–120V or 220–240V, 50–60Hz
Maximum power consumption: 1.5kW
Dimensions W x H x D (including feet, control knob and speaker terminals): 433 x 425 x 177mm
Weight (net): 18kg
Weight (gross): 19.7kg

Audio Specifications

Two channels driven, 4Ω / 8Ω, 20Hz – 20kHz 380W / 225W
One channel driven, 8Ω bridged mode, 20-20kHz 790W
Harmonic distortion, 80% power, 8Ω at 1kHz 0.001%
Input sensitivity 200W / 8Ω 1.15V RMS (RCA Type), 2.3V RMS (XLR Type)
Signal/Noise ratio (A-wtd) 50W / 8Ω 110dB
Input impedance 10kΩ
Frequency response 20 - 20kHz +/-0.05dB
Mains voltage 110–120V or 220–240V, 50–60Hz
Maximum power consumption 1.5kW
Dimensions W x H x D (including feet, control knob and speaker terminals) 433 x 425 x 177mm
Weight (net) 18kg
Weight (gross) 19.7kg



Parašyti savo apžvalgą

Jūsų apžvalgos: JBL SDA-2200 2-jų Kanalų Garso Stiprintuvas 2 x 4Ω / 8Ω, 20Hz – 20kHz: 380W / 225W dažnių juosta 20 - 20kHz +/-0.05dB | Nemokamas Pristatymas

Kaip įvertintumėte šią prekę? *

  1 balas 2 balai 3 balai 4 balai 5 balai
Kokybė